How to Make a Bottle Cap Party Whistle

Sometimes the things you least expect can come in handy. What if you were to get lost? Maybe an empty aluminum drink can will help you. This could be very helpful if you were to get lost because whistling takes a lot less effort than shouting. Start reading from step one below.

Steps

  1. Image titled Make a Bottle Cap Party Whistle Step 1
    1
    Take an empty aluminum drink can.
  2. Image titled Make a Bottle Cap Party Whistle Step 2
    2
    Use a pair of scissors to make some strategic cuts.
  3. Image titled Make a Bottle Cap Party Whistle Step 3
    3
    Take the sheet of aluminum foil. Make sure you save at least 2 tabs.
  4. Image titled Make a Bottle Cap Party Whistle Step 4
    4
    Cut along narrow strip from the sheet metal. Make sure the edges are straight as possible.
  5. Image titled Make a Bottle Cap Party Whistle Step 5
    5
    Then cut the smaller stubbier piece as well. The long strip is for the single can tab, while the smaller is a wide.
  6. Image titled Make a Bottle Cap Party Whistle Step 6
    6
    Join these pieces together, the smaller rectangle centered on top.
  7. Image titled Make a Bottle Cap Party Whistle Step 7
    7
    Wrap around the back holding it in place and snip the top corners off.
  8. Image titled Make a Bottle Cap Party Whistle Step 8
    8
    Fold the tab over to lock everything together. We now formed the mouthpiece for our whistle.
  9. Image titled Make a Bottle Cap Party Whistle Step 9
    9
    Grab the other end of the strip and push it back through the mouthpiece. Be careful, not to bend it.
  10. Image titled Make a Bottle Cap Party Whistle Step 10
    10
    The bottle cap.Get 2 clean bottle caps.
  11. Image titled Make a Bottle Cap Party Whistle Step 11
    11
    Use the scissors, snip the sides of the caps.
  12. Image titled Make a Bottle Cap Party Whistle Step 12
    12
    Cut a little notch in each caps. Make sure the two bottoms are lined up.
  13. Image titled Make a Bottle Cap Party Whistle Step 13
    13
    Form a round container with a symmetrical hole at the top.
  14. Image titled Make a Bottle Cap Party Whistle Step 14
    14
    The final product.Get the aluminum drink can that you made earlier. Then fit the barrel inside one of the caps.
  15. Image titled Make a Bottle Cap Party Whistle Step 15
    15
    Put some hot -glue inside the caps.
  16. Image titled Make a Bottle Cap Party Whistle Step 16
    16
    Then placed the rounded strip back in position
  17. Image titled Make a Bottle Cap Party Whistle Step 17
    17
    Carefully, cut the strip so it lines up the top of the notch.
  18. Image titled Make a Bottle Cap Party Whistle Step 18
    18
    Pull the scrap part out of the mouthpiece.
  19. Image titled Make a Bottle Cap Party Whistle Step 19
    19
    Add the hot-glue to other cap.
  20. Image titled Make a Bottle Cap Party Whistle Step 20
    20
    Press the two firmly together.
  21. Image titled Make a Bottle Cap Party Whistle Step 21
    21
    Cut one of the tabs in half and hot –gluing it to the back.
    • And now we already made a whistle with the used of empty drink can. You can add yard to make the whistle fully accessible anytime you want.

Warnings

  • Cutting aluminium is extremely hazardous. Be very careful to not cut yourself on the razor sharp edges of your cut up drinks can.
  • Ensure there are no sharp edges on your finished whistle before putting it anywhere near your mouth.
  • The finished product is not suitable for babies or small children.

Article Info

Categories: Hobbies and Crafts